How To Install A Key Safe

The popularity of key safes has increased over the last few years and they are the perfect solution for people with elderly family members, holiday lets or Air BnB’s. Within this article, we walk you through the steps on how to install a key safe with ease.

Tweet Pin It
How To Install A Key Safe
Darimo is reader-supported and we may earn an affiliate commission if you buy through links on our site. Find out more.

Key safes are a great bit of kit that are designed to be installed by anyone and without the need of a professional. Most brand’s include all of the hardware required to install a key safe within the box as well as instructions. However, if you are yet to purchase a key safe yourself, we have a guide that shows how to install a key safe in just six steps.

As you can see in the image above, we installed the best rated key safe to one of our properties. It’s known as the Supra C500 and it’s a police approved key safe that we would highly recommend.

Where To Put A Key Safe

Before you even begin to install a key safe, you will want to decide upon a location to put it. The best location to put a key safe is somewhere that’s out of view but still receives some light for anyone that uses it. Ideally, you also want it to be easily accessible without having to reach or bend over in awkward positions. Most brand’s will also state that it shouldn’t be installed upon the edge of a wall and it should be at least 6 inches away.

What You’ll Need

  • Corded hammer drill and masonry drill bit
  • Red plugs and screws (usually included in the pack)
  • Screwdriver
  • Hammer
  • Pencil and tape
  • Spirit level (optional)

How To Install A Key Safe


1. Set The Code

Before you begin to install your key safe, it’s recommended to set the code beforehand as it’s much easier to do it now before its mounted to the wall.

2. Drill Mounting Holes

Use the mounting hole template to mark the drill holes in the wall. Once the holes have been marked out, drill the holes using a corded hammer drill and a masonry bit.

3. Clear Any Dust & Debris

Before placing in any of the rawlplugs, use a brush to clear away any dust and debris.

4. Position The Key Safe

Position the key safe so that the newly drilled holes line up with screw holes inside.

5. Tighten The Screws Inside

Tighten each of the screws required to mount the key safe. You’ll want to tighten each screw bit by bit and ensure that the screw heads are fit snugly against the back of the key safe.

6. Test Locking & Unlocking

Now that you have installed the key safe, you can test that the code works and that it securely locks in place.

how to fit a key safe

How To Change The Code

Depending upon the key safe you are using will determine the method to which you change the code. However, the majority follow similar steps in order to change the code on the key safe:

  • Open the cover
  • Press and hold the “clear” button
  • Enter the existing code and then turn the open dial
  • Slide the plastic instruction card on the lid and remove
  • Turn the open dial back to its locked position
  • Use the plastic instruction card to turn all the grey dials to the “off” position
  • Use the card to turn the grey dial 180 degrees until the button pops back up completely
  • Set your new code and then place the card over the back of the lid
  • Test that the new code works

How To Open It Without A Code

If you need to open a key safe without a code, you can do so by removing it from the wall. This can be achieved by locating the screws from within the vault and using heavy duty power tools to gain access to the screws.

Conclusion

Although a key safe is relatively easy to install, you will want to follow the brand’s instructions very carefully. The reason we are stating this is because it may invalidate the security rating certification as well as any warranty. The above steps walk you through everything you need to know regarding the installation of key safes. However, depending upon the key safe you choose, there may be some differences due to the amount of different key safes on the market.

The Author Who Worked On This Article

author dan darimo

Dan Morgan

As a keen DIY’er, gardener and somebody that loves the latest tech, Dan is someone that brings years of experience in multiple trades. Since buying his first house, he has been obsessed with renovating properties and filling it with the latest products. This has led him down the road of testing hundreds of products and creating in-depth “how-to” and informative guides that offer his first-hand experience. Other interests include working on cars, keeping fit through sports or his home gym, caravanning and drinking great coffee.

If you would like to read more about Darimo and the authors, you can visit our about page. This goes into great detail regarding how we test products, create our guides and everything else.

Follow #DarimoUK

Copyright © 2021. All rights reserved.